Donanım Sorunları > Synology Donanım Problemleri

dosya aktarim

(1/2) > >>

ilhan macit:
sorunum, daha once boyle bir problem yoktu ama suan pc den nas a aktarilan dosyalarin hizi 3.25 mb i gecmemekte. daha once 10 mb a kadar sorun olmuyordu. hiz limiti sinirlandirmalarinda admin olarak bir sinirlandirma yok. Tepeden tirnaga baktim ama maselsef sorunu daha cozebilmis degilim. hiz limiti ayarlarinda adminler devre disi ama 3 mb yi gecmiyor aktarim. sizce ihtimaller ne olabilir. simdiden tesekkurler

SinanBedir2:
Merhabalar,

telnet yada ssh aracılığı ile dmesg çıktısının son 30-60 satırını burada paylaşabilir misin ?

ilhan macit:
Buyur ustad.


[   41.500000] Brand: Synology
[   41.500000] Model: DS-411
[   41.510000] This is default settings: set group disks wakeup number to 1, spinup time deno 1
[   41.970000] eth0: mac address changed
[   43.990000] eth0: link down
[   43.990000] eth0: started
[   43.990000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   45.020000] md: md2 stopped.
[   45.130000] md: bind<sda5>
[   45.130000] raid1: raid set md2 active with 1 out of 1 mirrors
[   45.140000] md2: detected capacity change from 0 to 495259287552
[   45.180000]  md2: unknown partition table
[   47.360000] EXT4-fs (dm-0): barriers disabled
[   47.410000] EXT4-fs (dm-0): mounted filesystem with writeback data mode
[   53.620000] ata1.00: configured for UDMA/133
[   53.620000] ata1: EH complete
[   53.890000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   53.900000] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   53.900000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   53.940000] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   53.960000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   53.980000] usb usb1: configuration #1 chosen from 1 choice
[   53.980000] hub 1-0:1.0: USB hub found
[   53.980000] hub 1-0:1.0: 1 port detected
[   54.130000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   54.310000] usb 1-1: new high speed USB device using orion-ehci and address 2
[   54.400000] Initializing USB Mass Storage driver...
[   54.410000] usbcore: registered new interface driver usb-storage
[   54.410000] USB Mass Storage support registered.
[   54.470000] usbcore: registered new interface driver usblp
[   54.480000] Got empty serial number. Generate serial number from product.
[   54.490000] usb 1-1: configuration #1 chosen from 1 choice
[   54.500000] hub 1-1:1.0: USB hub found
[   54.500000] hub 1-1:1.0: 4 ports detected
[   54.850000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   54.850000] usb 1-1.1: new high speed USB device using orion-ehci and address 3
[   54.870000] usbcore: registered new interface driver hiddev
[   54.880000] usbcore: registered new interface driver usbhid
[   54.880000] usbhid: v2.6:USB HID core driver
[   55.030000] Got empty serial number. Generate serial number from product.
[   55.030000] drivers/usb/core/hub.c (2019) Same device found. Change serial to d6a3ebcbfbd5e7a5f6a0
[   55.090000] usb 1-1.1: configuration #1 chosen from 1 choice
[   55.100000] hub 1-1.1:1.0: USB hub found
[   55.100000] hub 1-1.1:1.0: 4 ports detected
[   55.280000] nf_conntrack version 0.5.0 (7987 buckets, 31948 max)
[   56.150000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   63.200000] eth0: link up, full duplex, speed 100 Mbps
[   63.200000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   74.020000] eth0: no IPv6 routers present
[   76.920000] loop: module loaded
[   77.490000] Slow work thread pool: Starting up
[   77.930000] Slow work thread pool: Ready
[   79.540000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   80.440000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   80.450000] NFSD: starting 90-second grace period
[   90.120000] findhostd uses obsolete (PF_INET,SOCK_PACKET)
[   93.220000] usbcore: registered new interface driver snd-usb-audio
[ 5052.910000] eth0: link down
[ 5074.560000] eth0: link up, full duplex, speed 100 Mbps
[18756.810000] eth0: link down
[18784.350000] eth0: link up, full duplex, speed 100 Mbps
[18789.720000] eth0: link down
[18811.460000] eth0: link up, full duplex, speed 100 Mbps

ilhan macit:
ssh ile daha detayli alabilecegim komut yada system varsa belirtirseniz o sekilde de alirim. tesekkurler

SinanBedir2:
Hocam Merhaba,

[ 5052.910000] eth0: link down
[ 5074.560000] eth0: link up, full duplex, speed 100 Mbps
[18756.810000] eth0: link down
[18784.350000] eth0: link up, full duplex, speed 100 Mbps
[18789.720000] eth0: link down
[18811.460000] eth0: link up, full duplex, speed 100 Mbps

Ethernette sürekli kopmalar oluyor mu ?

Navigasyon

[0] Mesajlar

[#] Sonraki Sayfa

Tam sürüme git